Universal 4 Bike Hitch Rack Foldable Carrier for SUV 2 in Receiver

Description:

Welded Alloy Steel With A Finish That Holds: This heavy duty 4 bike hitch rack is built on an all alloy steel frame rather than a light tubular shell. The mast and both carry arms are cut, formed and welded as one structure, then finished with a powder coat that stands up to gravel spray, road salt and long sun exposure. Steel arms take the load at every contact point, and each bike sits in its own rubber cradle pad instead of resting on bare metal. The cradle rubber is UV resistant, so it stays soft and grippy instead of going brittle on a vehicle that lives outdoors. Every unit is checked for weld quality and cradle alignment before it is put into stock.

Rated For 140 lb Across Four Bikes: The rack carries up to four bikes on a combined load capacity of 140 lb, which covers a family of four riding a mix of adult and kids frames. Two carry arms spread the frames apart so handlebars, pedals and derailleurs are less likely to touch, and the mast is kept tall so loaded bikes sit well clear of the ground on steep driveway ramps and rough trailhead tracks. The tilt down feature drops the loaded rack away from the tailgate so a hatch or liftgate opens without taking bikes off first. When the rack is empty, the arms fold up against the mast so the vehicle keeps a shorter rear profile in traffic and in a garage.

Where It Earns Its Place: Think about the trips this 4 bike carrier hitch mount is made for. A weekend at the beach or the lake, a camping run with a camper or travel trailer behind the vehicle, a shuttle of kids bikes to the trailhead, and a shop van moving customer bikes between two sites. Minivan and SUV owners use it for family holidays, pickup owners fit it for shuttle duty on event days, and many drivers move the same rack between a second car and a work truck because it needs nothing more than a standard receiver. It is a carrier for people who ride often and want the bikes with them every time.

Slides Into A Standard 2 in Receiver: Compatibility is deliberately simple. The shank is made for a standard 2 in receiver tube on cars, trucks, SUVs, vans and minivans, and assembly is a one time job that needs minimal tools. The carry arms can be fitted on the left or the right, so one person can build the rack on a bench before it goes on the vehicle. The supplied anti rattle hitch tightener takes the play out of the receiver, and the strap adds a second line of retention over the loaded frames. The included cross bar adapter fits step through and kids frames that have no straight top tube, so smaller bikes hang level with the rest.

Four Places And One Bike Each: The rack holds four bikes in four separate places. Every frame sits in its own pair of adjustable cradles on its own set of straps, and each pair of bikes rides on a separate arm, so no frame leans against another and no strap is shared. Where a cradle sits along the arm sets the gap to the next bike, which closes up for narrow handlebars and opens out for a long wheelbase. A step through or kids frame goes on with the cross bar adapter, which lifts it to the same angle as the adult bikes so all four hang level, and the strap takes up the rest of the slack on each frame. Each bike is released on its own

Held Down On Three Levels: Safety here is layered rather than assumed. The anti rattle hitch tightener clamps the shank inside the receiver so the rack cannot rock or creep its way back out during a drive, and the dual carry arms place every bike in its own rubber cradle instead of stacking frames against each other. A retaining strap secures the load as a backup to the cradle straps, so a frame that shifts on a rough road is still held. The tilt down mechanism stays locked until it is deliberately released, so the loaded rack does not swing away from the tailgate on its own once it is set.

Steel And Rubber Built To Be Renewed: Durability comes from the materials and the way the parts fit together. An all steel frame under a powder coat resists the two things that attack a carrier hardest: road salt on treated roads and standing water after a wash. UV resistant cradle rubber and straps flex instead of cracking, and because cradles, straps and the tightener are separate fittings, a worn strap can be renewed without retiring the rack. Bolted joints can be re torqued during routine checks, and the welded mast holds its shape under load instead of spreading.

From The Hitch To The Trailhead In Minutes: The rack arrives needing minimal tools and one time assembly, and the arms can be mounted on either side, which suits loading from the left or the right. Once it is on the receiver, the tilt down release drops the loaded rack away from the tailgate in a single motion, so the rear door opens without unloading. The cross bar adapter clips onto a frame with no straight top tube in seconds and moves between bikes as riders change. When the rack is not in use, the arms fold flat to the mast and the assembly stays on the vehicle, ready for the next trip.

From The Hitch To The Trailhead In Minutes: The rack arrives needing minimal tools and one time assembly, and the arms can be mounted on either side, which suits loading from the left or the right. Once it is on the receiver, the tilt down release drops the loaded rack away from the tailgate in a single motion, so the rear door opens without unloading. The cross bar adapter clips onto a frame with no straight top tube in seconds and moves between bikes as riders change. When the rack is not in use, the arms fold flat to the mast and the assembly stays on the vehicle, ready for the next trip.

One Set Of Fittings Across The Range: Every wearing part on this 4 bike hitch rack is a separate fitting, so cradles, cradle straps, hitch tightener, cross bar adapter and retaining pin each fit and remove on their own, and a rack is put back to full working order with one fitting rather than a whole assembly. Those fittings share one set of tolerances, which means a pin, cradle or strap that follows the same drawing seats on any rack in the range, and one spare set covers each size. Each fitting carries the part number of its drawing, and that number keys its dimensional and coating inspection records, so a specification is confirmed from the drawing rather than from a description.

Q1. What is your MOQ ?

A:For stock :10 PC , Customization: Minimum order quantity ranges from 10 to 1000 pieces per product. Please consult our sales representatives for specific quantities.

Q2. Does the product meet European and American certification standards?

Our products are certified to European and American standards, including CE, ISO, and DOT certifications. Additionally, we hold dozens of design patent molds, ensuring market protection for your purchases or sales.

Q3.What are your advantages compared with others?

A: 1. With our own factory to manufacture the products, we can ensure timely products delivery

2.Owned factory, the same quality product. the best price

3. We have professional staffs, let you enjoy comfortable and effective communication

4. More efficient management in every process.

Q4.How do you control your quality?

A: 1.Selecting good steel material, producing follow the standard, proper inspection of products

2.100% finished product testing

3.Iso quality management system certificated factory

4.We accept inspection of products.

Q5. Can I order a sample with my own design /logo ?

Yes, our design team can create samples based on your sketches, images, or designs. If you have uncertainties about the product, we can first produce a 3D printed model for your review before proceeding with the formal sample production

Q6: Can I get a free sample ?

A:Because many customers want it, and development cost is too high, we cannot provide free samples, but when you place an order ,the sample cost can be refund to you .

Q7: What is your Sample Lead-Time ?

A: Within 5 working days after confirm all details. If busy season, about 7 working days.

Q8:Can I get a quote for the products I need?

Of course, you can send us an inquiry and provide product dimensions along with detailed images (front, side, back, internal structure, etc.). This will help us provide a more accurate quote. We would be happy to send you a quote.

Q9: What about the delivery day?

Typically 7 to 35 days, depending on the complexity and quantity of the product. You can confirm with us based on your specific prod，We accept 100% T/T payment before delivery, or 30% deposit and 70% before delivery.

Q10:Which kind of shipping way can choose ?

A: By air or by sea. If ship by express (UPS,DHL, FEDEX, EMS ), Shipping time 5-7 days ,except the EMS(EMS is the cheapest way but take more time ). By air : shipping time 12-15 days (the products can't less 22 KG) . By sea (has the different Time-based can choose, within 25 days, 30-35 days , 50-60 days ).some country can shipping by train or truck. you can decide suitable shipping way according to what your need.

Q11:Which kind of shipping way can choose ?

A: Accepted Delivery Terms: FOB, CFR, CIF, EXW, DDP, DDU

Accepted Payment Currency: USD, EUR, JPY, CAD, AUD, HKD, GBP, CNY, CHF

Accepted Payment Type: T/T,L/C,D/P D/A, MoneyGram, Credit Card, Western Union, Cash, Escrow

Language Spoken: English, Chinese, Spanish, Japanese, Portuguese, German, French, Arabic, Russian, Korean.