Recessed D Ring Tie Down Anchors 4 Pack 6000 lbs for Trailer Truck Bed

Description:

Forged Carbon Steel with an Electro-Galvanized Finish: Each recessed anchor is forged from high strength carbon steel and machined to a 1/2 inch ring opening that accepts standard strap hooks, ratchet strap end fittings and rope terminals. The forged body then passes through an electro-galvanizing line that deposits a uniform zinc layer over the ring, the housing and the backing plate, reaching inner surfaces, cavities and threaded mounting holes that a top applied finish cannot cover. The zinc layer works as a sacrificial barrier, holding road salt, fertilizer and wash down chemicals back from the steel and protecting the plating edges where the surface is scuffed. Plated surfaces release mud and grit with a wipe and keep a clean face through repeated wash down. Ring, housing, backing plate and mounting hardware ship as a matched set, with every part of the assembly carrying the same rated capacity.

6000 lbs Working Load Limit and 12000 lbs Breaking Strength: Every single anchor in the pack is rated at 6,000 lbs working load limit and 12,000 lbs maximum breaking strength, a 2:1 margin between the rated working load and the failure point. The load path runs from the ring, through the housing, into the reinforced backing plate and out through the four mounting points. A four bolt pattern spreads that load across a wider section of the deck than single bolt or double bolt anchor plates, lowering the stress carried by each mounting point. The rating holds for each anchor individually, letting a deck be planned around the number of tie down points a given load requires.

Cargo Securement for Trailers Truck Beds and Open Decks: Flush recessed anchors take motorcycle ratchet straps, bungee cords, tarp straps and trailer ropes without adapters. Typical installations cover enclosed trailers, flatbeds, pickup beds, cargo vans, boat decks, equipment trailers and UTV or ATV haulers. Loads handled in service include motorcycles, ATVs, UTVs, machinery, furniture, cargo boxes, pallets and power tools. Placing anchors in a grid gives each machine its own four point tie down pattern, holding the load down against the deck through braking, cornering and rough pavement without leaning on a single strap run. Reducing cargo bounce, shift and sway protects the deck surface and the equipment riding on it.

Bolt On Recessed Mount with a Four Bolt Backing Plate: Installation calls for a drilled hole, a hole saw for the recess pocket and the included mounting screws. Standard packs ship with four anchors and the full screw set, while the 90 mm hole saw bundle adds the cutter for the pocket in a single order. The ring sits inside its housing under spring tension and rides below the deck line when no strap is attached, which keeps pallets, dollies and sliding cargo moving over a flat surface. Deck thickness, the material behind the mounting face and the clearance under the panel all matter, since the backing plate sits on the underside of the mounting surface.

Order Programs and Batch Consistency: Orders ship in cartons of matched anchors with mounting hardware, and carton counts, label wording and pallet patterns stay the same from run to run. Private label printing, custom poly bag counts and mixed container loading alongside other cargo hardware are available on program orders. Working load limit and breaking strength figures are printed on the batch documentation, keeping catalog listings, safety data sheets and import paperwork aligned with the goods on the pallet. Sample packs are available for fit checks on a specific deck or panel, and replacement hardware is stocked separately from complete kits.

Rated Load Margin Across a Four Bolt Load Path: A 6,000 lbs working load limit against 12,000 lbs maximum breaking strength leaves a 2:1 margin between daily working load and the failure point, giving fleet specifiers and safety reviewers room to work with. The reinforced backing plate and 4 bolt pattern spread force across a wider footprint than single bolt or double bolt plates, lowering stress at each mounting point and reducing the chance of panel deformation under shock loads. Spring tension holds the ring inside the pocket when it is not in use, cutting metal rattle and the load shift that follows from it on rough pavement.

Longer Service Life per Anchor: The dual layer finish is where the cost argument sits. Electro-galvanizing carries the corrosion barrier against road salt, fertilizer and wash down chemicals, and the powder coating over it takes the abrasion from gravel, steel decking and sliding pallets. Coated surfaces clean up with a wipe, keeping inspection and maintenance labor low across a season of hauling. A four pack covers a full trailer floor or truck bed in one order, and a set that holds its load rating and finish through repeated cycles replaces fewer units over the life of the vehicle.

Straightforward Installation and Daily Handling: Every pack includes the four anchors and the full mounting screw set, and the optional 90 mm hole saw bundle delivers the cutter for the recess pocket in the same order. The ring retracts under spring tension and sits flush with the deck line, letting cargo slide over the anchor point without catching on it, and hooking a strap is a one hand operation. There is no protruding hardware to snag gloves, tarps or webbing during loading, and no adapter is needed for ratchet straps, bungee cords, tarp straps or trailer ropes.

CE ISO and SAE J684 Compliance: The anchors are produced to CE marking requirements, and the manufacturing line operates under an ISO 9001 quality management system covering material traceability, forging controls and coating thickness checks. SAE J684 test references are applied to the load bearing assembly, and the resulting documents travel with each batch. Test reports, declarations and batch records are issued in English for customs clearance, technical file assembly and listing review, giving importers a clean paper trail from purchase order to container release.

Supply Chain and Order Service: Production runs on schedule against released purchase orders, with stable carton specifications, pallet configurations and container load plans that keep landed cost predictable. Private label printing, custom packaging quantities and combined shipments with other trailer and cargo hardware are handled on program orders. Batch records, rating documentation and replacement hardware ship with the goods, and a technical contact answers fit, rating and document questions before the order is placed. Orders move from sample to full container without a change in specification.

Q1. What is your MOQ ?

A:For stock :10 PC , Customization: Minimum order quantity ranges from 10 to 1000 pieces per product. Please consult our sales representatives for specific quantities.

Q2. Does the product meet European and American certification standards?

Our products are certified to European and American standards, including CE, ISO, and DOT certifications. Additionally, we hold dozens of design patent molds, ensuring market protection for your purchases or sales.

Q3.What are your advantages compared with others?

A: 1. With our own factory to manufacture the products, we can ensure timely products delivery

2.Owned factory, the same quality product. the best price

3. We have professional staffs, let you enjoy comfortable and effective communication

4. More efficient management in every process.

Q4.How do you control your quality?

A: 1.Selecting good steel material, producing follow the standard, proper inspection of products

2.100% finished product testing

3.Iso quality management system certificated factory

4.We accept inspection of products.

Q5. Can I order a sample with my own design /logo ?

Yes, our design team can create samples based on your sketches, images, or designs. If you have uncertainties about the product, we can first produce a 3D printed model for your review before proceeding with the formal sample production

Q6: Can I get a free sample ?

A:Because many customers want it, and development cost is too high, we cannot provide free samples, but when you place an order ,the sample cost can be refund to you .

Q7: What is your Sample Lead-Time ?

A: Within 5 working days after confirm all details. If busy season, about 7 working days.

Q8:Can I get a quote for the products I need?

Of course, you can send us an inquiry and provide product dimensions along with detailed images (front, side, back, internal structure, etc.). This will help us provide a more accurate quote. We would be happy to send you a quote.

Q9: What about the delivery day?

Typically 7 to 35 days, depending on the complexity and quantity of the product. You can confirm with us based on your specific prod，We accept 100% T/T payment before delivery, or 30% deposit and 70% before delivery.

Q10:Which kind of shipping way can choose ?

A: By air or by sea. If ship by express (UPS,DHL, FEDEX, EMS ), Shipping time 5-7 days ,except the EMS(EMS is the cheapest way but take more time ). By air : shipping time 12-15 days (the products can't less 22 KG) . By sea (has the different Time-based can choose, within 25 days, 30-35 days , 50-60 days ).some country can shipping by train or truck. you can decide suitable shipping way according to what your need.

Q11:Which kind of shipping way can choose ?

A: Accepted Delivery Terms: FOB, CFR, CIF, EXW, DDP, DDU

Accepted Payment Currency: USD, EUR, JPY, CAD, AUD, HKD, GBP, CNY, CHF

Accepted Payment Type: T/T,L/C,D/P D/A, MoneyGram, Credit Card, Western Union, Cash, Escrow

Language Spoken: English, Chinese, Spanish, Japanese, Portuguese, German, French, Arabic, Russian, Korean.